Burner Design Using Used Oil Fuel Based on Water Vapor Pressure
DOI:
https://doi.org/10.31004/jestm.v5i2.271Keywords:
Burner design, Waste incineration , Efficiency, Used oil , Water vaporAbstract
This research aims to design and build an environmentally friendly burner that integrates used oil as a fuel based on water vapor pressure and to test the waste combustion efficiency using the designed device. The design stage of the device uses the assistance of AutoCAD. This is followed by direct experimental testing to collect data on the performance and efficiency of waste combustion in the burner. Based on the results of the two burners that have been tested above, it can be concluded that the amount of shrinkage of 8 kg of waste burned in a used oil burner with water vapor pressure is more shrinkage than the used oil burner without water vapor with a difference of 1.1 kg. This can be proven in the best experimental results in the first experiment, namely to burn 8 kg of waste in 25 minutes experiencing a shrinkage of 7.1 kg, so that the efficiency of waste combustion reaches 88.75% in a used oil burner with water vapor pressure. While the used oil burner without water vapor obtained the best results for burning 8 kg of waste in 25 minutes experiencing a shrinkage of 6 kg, so that the efficiency is 75% lower than combustion using a used oil fuel burner using water vapor pressure.
References
Ariansyah, P. M., & Wijaya, K. (2021). Design and construction of a web-based academic information system: Case study SD Negeri 18 Tanah Abang.
Azzikri, M. F., Azriadi, E., & Rusnedy, P. (2024). Design and construction of a stove using used oil.
Butar, I. D. B., Yusuf, M., Nayan, A., & Aljufri, A. (2024). Design and development of a burner stove using used fuel oil.
Farid, A. (2020). Analysis of steam flow velocity in the application of household waste utilisation as a combustion medium in boiler design.
Gunawan, R., Yusuf, A. M., & Nopitasari, L. (2021). Design and construction of a student attendance system using Android-based QR codes.
Hata, A., Azmy, I., Adityo, H. D., & Murhaban, M. (2023). Design and construction of a PET plastic waste melting tool using used oil as fuel.
Mafruddin, M., Ridhwan, K., Budiyanto, E., Kurniawan, K., Mubarak, M. A., & Pratama, N. B. (2022). The effect of air flow rate and water vapor holes on the performance of stoves using used oil fuel.
Nugroho, A. S., Rahayu, A. T., & Rubiadana, N. A. (2021). Experimental study of the effect of nozzle diameter on the combustion of liquid waste fuel.
Ria, N. A. (2022). Analysis of product distribution strategies in maintaining product life cycles from an Islamic economic perspective.
Sarofah, M. (2022). Analysis of the application of circular economy system in waste recycling management at Kamandaka Recycling Centre.
Shahab, A., & Amna, S. (2023). Efficiency analysis of fire tube boiler type at refinery utility unit center for oil and gas human resources developme
Siagian, D. P., Widodo, A. S., & Ud, F. G. (2018). The effect of water vapor content on laminar flame speed with methane fuel. Brawijaya University.
Siregar, H. F., & Sari, N. (2018). Design and construction of a web-based money saving and loan application for students of the Faculty of Engineering.
Sulistyanto, H., Syafira, I. M., Isnaini, A. Q., Prasetyo, F. H., Qolby, W., Pramita, E., & Khusain, R. (2020). Habituation of waste management as a character education strategy for environmental awareness among students of MI Muhammadiyah Cekel, Karanganyar.
Yusnita, Y., Ditasman, D., Putra, M. B. E., Hidayat, R., & Noviranda, H. (2024). Increasing the knowledge of the Penembang village community, Merigi Kelindang sub-district, Central Bengkulu Regency about good waste disposal management
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Afrinaldi, Emon Azriadi, Hidayati Rusnedy
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
